NZXT H9 Elite Mid Tower Case
Trendy panoramic panoramic chassis, if you like to show off your own computer, you must not miss the NZXT H9 Elite Mid-Tower chassis, which has excellent internal chassis design, excellent heat dissipation design as the selling point, the front and the tempering side. glass There is no bracket design between the side panels, there is absolutely no obstacle to achieve 90 ° no dead angle display, allowing the internal hardware to be fully displayed, adding a Dual Chamber double cabin, vertical air duct heat dissipation design , completely breaks the traditional chassis frame, just like putting Just like a computer goldfish tank, players who like to play RGB and water cooling just like it.
The first impression of HZXT H9 Elite is the simple aesthetics. The characteristics of the HZXT chassis are combined with the Panoramic panoramic design, and the Dual Chamber air duct double air duct cooling design is specially added. the lower power supply is moved to the right, left The side is the installation area of the motherboard. The horizontal design can reduce the height of the fuselage and introduce cold air from the bottom to compensate for the shortcomings of the panoramic design Panoramic that the wind cannot go into the front. The extra-large cable management layer design also makes cable management easier.
The NZXT H9 series is available in two versions, Flow and Elite. The Flow version uses a metal vent panel at the top, without fans and RGB controllers, but the price is more accessible. The Elite version uses a tempered glass panel at the top and comes with 280 / 360 water cooling fans The mounting bracket is attached with 3 Duo RGB F120RGB fans and NZXT RGB & Fan Controller V2 controllers, both available in black and White.
A large number of air holes are added to the right metal panel, mainly for the side fans or radiators The whole right panel is covered with a dust filter, so there is no need to worry about dust going in In order to strengthen the stability of the corners of the glass panel, a reinforced metal frame is added instead of opening holes in the glass, so that the point of force is absorbed and weighted by the metal frame, reducing the risk of cracking . the corners, and there is no drilling on the glass side plate for positioning Installed by means of pins, assembly and disassembly without tools makes it easier for players to assemble.
The Elite NZXT H9 chassis I/O Panel is located on the top right, providing a Power switch button, 2 sets of USB 3.0 Type A 5Gbps ports, 1 set of USB 3.2 Gen 2 Type C 10Gbps ports, and 1 set of 3.5mm audio interfaces More and more gaming headsets use 4-pole plugs, so the factory has switched to a 4-pole 3.5mm audio connection port, which can provide audio and microphone functions at the same time with a single cable, without the need to install additional slots separately.
Support ATX motherboard, vertical air duct design
NZXT H9 Elite is made of SGCC hot dip galvanized sheet, ABS plastic and sound absorbing materials, size is 505mm x 230mm x 480mm, and the net weight is 13.1kg It can support Mini-ITX, Micro-ATX and ATX motherboards , and supports CPU heat dissipation up to 16.5cm The main room has NZXT’s iconic cable cover, which not only makes the inner cage more fashionable, but also covers most of the wires to keep the internal space is neat. This design is also a signature feature of NZXT cases.
In terms of graphics cards, the NZXT H9 Elite Mid-Tower case supports displays up to 43.5cm long and has PCIe 7 expansion slots. Although the official NZXT website will show a vertical graphics card layout, it actually has no built-in support for vertical installation. Additional purchase of the Vertical GPU Mounting Kit is required to support it.
Double cabin interior design
The interior of NZXT H9 Elite adopts a Dual Chamber interior design. The left side is the motherboard installation area, and the right side is the power supply and storage device area. The horizontal design can reduce the height of the fuselage. There is an ugly panel in the middle and it can be used to install a 2.5-inch SSD. /HDD,
Extra-large cable management layer design also makes cable management easier and easier.
Remove the ugly cover and you can see the PSU power supply installation area and the ultra-deep cable management slot The power supply is mounted on the back of the motherboard and supports ATX power supplies up to 20cm (blue area) .The yellow one is the cable management slot with a depth of 9.1 cm, whether you are a beginner or not, this design also greatly reduces the installation difficulty, bringing a pure installation experience in full of ritual.
4 x 2.5″ + 2 x 3.5″ storage devices.
▲ 4 x 2.5” SSD/HDD ▲ 2 x 3.5” Drive Bay
The storage expandability of the NZXT H9 Elite chassis is good The chassis has a 3.5-inch Drive Bay on the cable management layer, which can support two 2.5-inch or 3.5-inch SSD / HDD devices. In addition, the back of the ugly board on the cable management layer provides four 2.5-inch SSD / HDD installation positions, and the entire chassis supports up to six 2.5-inch devices or four 2.5-inch + two 3.5- inch.
Comes with 3 F120RGB Duo fans
NZXT H9 ELITE has 3 Duo F120RGB fans attached to the side The Duo version has a front and back light ring design with 20 LED ring-shaped light guide rings. It supports 12V and PWM voltage input for speed control. The speed is 500rpm ~ 1800rpm ±10%, the maximum air flow rate is 48.58CFM, the maximum air pressure is 2.42mm H²O, the maximum sound and noise level is 29dBA, and the front end can support a maximum water-cooled heat exhaust of 360mm.
NZXT RGB & Fan Controller V2
NZXT H9 Elite is attached with a set of RGB controllers & Fan Controller V2, which provides 6 RGB control channels and 3 fan speed control channels, and each fan channel provides 1 output and 3 transmission interfaces, so it can support long to 9 controls For fans, users can control RGB lighting effects and fan speed through the NZXT CAM package.
In the NZXT CAM package, users can control the lighting effect of the F120RGB Duo fan. The preset provides 16 kinds of ARGB lighting effect mode control and brightness, which is quite rich.
On the cooling page of the NZXT CAM package, it provides speed control of 3 different fan channels, providing silence, high efficiency, stability and adjustment according to temperature.Support fan speed adjustment, users can automatically adjust the fan speed according to the CPU or GPU temperature, for example, I keep the fan speed at 20% at 20-30°C, 20% at 34-50°C , when above 50 ° C Automatically increases speed until 65 ° C fans come to full speed.
Can support three 360mm radiators
As the flagship model of the NZXT chassis, H9 Elite has a very large fan and radiator load capacity, including five positions at the top, bottom, back, bottom and side A total of up to 10 12cm fans can be installed. Three 360mm tower -cooled radiators allow for a variety of ways to play.
A 360mm transparent mounting bracket is preloaded on the top, which can support 3 12cm fans or 1 360mm cooling radiator, and a 280mm transparent mounting bracket is attached for replacement, which can support 2 14cm fans or 1 radiator cooling 280mm. The reason for the transparent mounting frame is to reduce the effect on the aesthetics of the top. If the top does not intend to install a fan or water cooling, the transparent mounting frame can be removed completely.
The base can support three 12cm fans or two 14cm fans, and the water cooling can support cooling radiators up to 280mm or 360mm. Players should try to use the bottom to introduce cold air to compensate for the shortcomings of the panoramic design Panoramic that can Do not let in the wind from the front, and at the same time bring more direct cooling graphics cards.
One F120Q cooling fan is preloaded on the rear side ︳can support one 120mm cooling radiator, and three F120RGB Duo cooling fans are preloaded on the side, which can support one 360mm cooling radiator. NZXT factory preload is to draw in Fresh air direction, if the user can install the bottom fan, it is recommended to reverse the direction of the F120RGB Duo fan to exhaust, the effect will be more ideal.
NZXT H9 Mid Tower Case
Price: HK$1,299 (Flow) / HK$1,769 (Elite)
Enquiries: Altech Computer (3628-3377)
Editor’s note:
NZXT H9 Elite has been well received by foreign players, especially the serious players who like to show off their own machines. If you don’t want to see your own machine from above all day, you can consider Flow H9. Actually, the cooling effect is better. It’s a shame. Without the RGB fan and the HUB, wow… it’s really hard to choose between Flow and Elite.
